- #Kct 19 installation in kenwood tk 880 install#
- #Kct 19 installation in kenwood tk 880 software#
- #Kct 19 installation in kenwood tk 880 password#
- #Kct 19 installation in kenwood tk 880 series#
Com 2(Internal Port) : Extended Function Program Com 2 as AUX Hoot/PTT While in the Optional Features screen, select Extended Function.
#Kct 19 installation in kenwood tk 880 password#
Busy LED : TX Inhibit Time : s Display Character : Transpond Delay Time : s Off Hook Decode : System Search : Off Hook Horn Alert : Clear to Talk : Horn Alert Time : s Free System Ring Back : Radio Password : Battery Warning : Data Password : Timed Power Off : Power On Text : Tone Feature. See the figure below for more information Optional Features System Name Text Size : T.O.T(Dispatch) : s Sub LCD Display : T.O.T(TEL) : s Conv. This enables the external PTT from the data terminal.
Although this may be the case, in order to enable a data terminal interface you must program Com 2 (Internal Port) as AUX Hook/PTT. Depending on your application, most of the parameters in the Optional Feature menu will be left at default. Trunking Programming Optional Features From the Edit pull down menu, select Optional Features. Select Trunking or Conventional Radio Format Conventional 2. Radio Format When programming the radio select trunking or conventional, make sure that you set the Radio Format correctly upon creation of your new profile.
#Kct 19 installation in kenwood tk 880 series#
3Ĥ Programming the Kenwood TK-x80 Series Mobile To begin programming your TK-x80 series mobile for use with the Pyramid Communications Model 2012/Merlin mobile data system, you will need to first create a new profile using your KPG-49D programming software. More programming instructions are available in the 2012/Merlin Service Manual. Chose the format to fit your application. There are three signaling format choices. Set I/O Pin 9 to Channel Change, Method Continuous From the Data pull down menu, select your Data Format in the Format Screen.
#Kct 19 installation in kenwood tk 880 software#
Note: Console needs to match programming the 2016 Console Software Vehicle #: 100 ( ) Base #: 1 (1-4) PTT Delay: 0.5 S (.1-2.5) Retries: 3 (0-9) Trunking mobile Yes Sequential Status No ANI on mobile PTT No Enable Time Stamp No COR Polarity High On Air Polarity High I/O Pin 9 Output Ch Cng Method Cont Enable Turnking Mode if applicable. Vehicle # and Base # will vary with your application. From the Data pull down menu, under the System Data screen, program the unit as shown the figure below. Start running the Pyramid 2012/Merlin programming software on your PC.
#Kct 19 installation in kenwood tk 880 install#
If you have not already done so, install the programming software on to your PC by following the instructions in the 2012/Merlin service manual. (2012 PTT transistor Q2, 2016 PTT transistor Q3) Programming the Pyramid 2012/Merlin The mobile data terminal needs to be programmed to accommodate the polarities of signal that the Kenwood mobile will provide it. Without this modification, you will experience no transmit audio out of the Kenwood 80 Series version-2 radios. Also, you will need a copy of the Pyramid 2012 programming software and FY-1 programming cable to program the ** In older versions of Pyramid Communications 20 units, you will need to replace the PTT transistor with a standard NPN (2N4401) transistor. 1 Programming Instructions for: Kenwood TK-780, 880, 980, 981 (Version 2) W/ KCT-19 Option Connector For use with: Pyramid Communications Model 2012/2016/Merlin Revision E November 25,Ģ Introduction.3 Programming the Pyramid 2012/Merlin.3 Radio Format.4 Programming Optional Features.4 Programming the Logic Signalling.5 Programming the Talk Group information for a 2012/Merlin MDT.5 Defining a Talk Group for Data Use.6 Programming the Pyramid Programming the Pyramid 2016 (Continued).8 Understanding Base Channel Change.9 Configuring your 2016 for Voice Channel Change.9 Programming the Kenwood TK-x80 Series Base Radio Format Programming Optional Features Programming the Logic Signalling Programming the Talk Group information for a 2016 Base Modem Wiring the Pyramid to the Kenwood TK-x Connecting the 2012/Merlin MDT to the TK-x80 radio Jumper Settings in the 2012/Merlin Connecting the 2016 base to the TK-x80 radio Supporting the Kenwood KDS-100 /w Merlin AVL Modifications To Kenwood TK-x80 Mobile Radio KDS-100 Modifications Merlin AVL Modificationsģ Introduction Before you begin, you will need to have a copy of KPG-49D and programming cable available to program the mobile radio.
0 kommentar(er)
